openHAB

This page is part of archived documentation for openHAB 4.3. Go to the current stable version

# Netatmo Binding

The Netatmo binding integrates the following Netatmo products:

  • Personal Weather Station. Reports temperature, humidity, air pressure, carbon dioxide concentration in the air, as well as the ambient noise level.
  • Thermostat. Reports ambient temperature, allow to check target temperature, consult and change furnace heating status.
  • Indoor Camera / Welcome. Reports last event and persons at home, consult picture and video from event/camera.
  • Siren
  • Outdoor Camera / Presence. Reports last event, consult picture and video from event/camera.
  • Doorbell
  • Smoke Detector
  • Smart Door Sensor
  • Carbon Monoxide Detector

See https://www.netatmo.com/ (opens new window) for details on their product.

# Binding Configuration

The binding requires you to register an Application with Netatmo Connect at https://dev.netatmo.com/ (opens new window) - this will get you a set of Client ID and Client Secret parameters to be used by your configuration.

# Create Netatmo Application

Follow instructions under:

  1. Setting Up Your Account
  2. Registering Your Application
  3. Setting Redirect URI and webhook URI can be skipped, these will be provided by the binding.

Variables needed for the setup of the binding are:

The binding has the following configuration options:

Parameter Type Description
readFriends Boolean Enables or disables the discovery of guest weather stations.

# Netatmo Account (Bridge) Configuration

You will have to create at first a bridge to handle communication with your Netatmo Application.

The Account bridge has the following configuration elements:

Parameter Type Required Description
clientId String Yes Client ID provided for the application you created on http://dev.netatmo.com/createapp (opens new window)
clientSecret String Yes Client Secret provided for the application you created
webHookUrl String No Protocol, public IP and port to access openHAB server from Internet
webHookPostfix String No String appended to the generated webhook address (should start with "/")
reconnectInterval Number No The reconnection interval to Netatmo API (in s)

Supported channels for the Account bridge thing:

Channel Group Channel Id Item Type Description
monitoring request-count Number Number of requests transmitted to Netatmo API during the last hour

# Configure the Bridge

  1. Complete the Netatmo Application Registration if you have not already done so, see above.
  2. Make sure you have your Client ID and Client Secret identities available.
  3. Add a new "Netatmo Account" thing. Choose new Id for the account, unless you like the generated one, put in the Client ID and Client Secret from the Netatmo Connect Application registration in their respective fields of the bridge configuration. Save the bridge.
  4. The bridge thing will go OFFLINE / CONFIGURATION_ERROR - this is fine. You have to authorize this bridge with Netatmo Connect.
  5. Go to the authorization page of your server. http://<your openHAB address>:8080/netatmo/connect/<_CLIENT_ID_>. Your newly added bridge should be listed there (no need for you to expose your openHAB server outside your local network for this).
  6. Press the "Authorize Thing" button. This will take you either to the login page of Netatmo Connect or directly to the authorization screen. Login and/or authorize the application. You will be returned and the entry should go green.
  7. The bridge will go ONLINE.

Now that you have got your bridge ONLINE you can now start a scan with the binding to auto discover your things.

Starting on 2023/04/17 - Netatmo API requires an update of the refreshToken provided by the oAuth mechanism every three hours. Once authentication process has been done, current refreshToken is stored in /OPENHAB_USERDATA/netatmo folder.

# List of supported things

Thing Type Type Netatmo Object Description Thing Parameters
account Bridge N/A This bridge represents an account, gateway to Netatmo API. clientId, clientSecret, username, password, webHookUrl, reconnectInterval
home Bridge NAHome A home hosting Security or Energy devices and modules. id, refreshInterval, energyId, securityId
person Thing NAPerson A person known by your Netatmo system. id
welcome Thing NACamera The Netatmo Smart Indoor Camera (Welcome). id, ipAddress
presence Thing NOC The Netatmo Smart Outdoor Camera (Presence) camera with or without siren. id, ipAddress
siren Thing NIS The Netatmo Smart Indoor Siren. id
doorbell Thing NDB The Netatmo Smart Video Doorbell device. id, ipAddress
weather-station Bridge NAMain Main indoor module reporting temperature, humidity, pressure, air quality and sound level. id, refreshInterval
outdoor Thing NAModule1 Outdoor module reporting temperature and humidity. id
wind Thing NAModule2 Wind sensor reporting wind angle and strength. id
rain Thing NAModule3 Rain Gauge measuring precipitation. id
indoor Thing NAModule4 Additional indoor module reporting temperature, humidity and CO2 level. id
home-coach Thing NHC Healthy home coach reporting health-index, temperature, humidity, pressure, air quality, sound level. id, refreshInterval
plug Thing NAPlug The relay connected to the boiler controlling a Thermostat and zero or more valves. id
thermostat Thing NATherm1 The Thermostat device placed in a given room. id
room Thing NARoom A room in your house. id
valve Thing NRV A valve controlling a radiator. id
tag Thing NACamDoorTag A door / window sensor id
smoke-detector Thing NSD A Smoke Detector id
co-detector Thing NCO A Carbon Monoxide Alarm id

# Webhook

Netatmo servers can send push notifications to the Netatmo Binding by using a callback URL. The webhook URL is setup at Netatmo Account level using "Webhook Address" parameter. You will define here public way to access your openHAB server:

http(s)://xx.yy.zz.ww:443

Your Netatmo App will be configured automatically by the bridge to the endpoint:

http(s)://xx.yy.zz.ww:443/netatmo/webhook/<_CLIENT_ID_><webHookPostfix>

Please be aware of Netatmo own limits regarding webhook usage that lead to a 24h ban-time when webhook does not answer 5 times.

NB: Allowed ports for webhooks are 80, 88, 443 and 9443.

# Configure Things

The easiest way to retrieve the IDs for all the devices and modules is to use the console command openhab:netatmo showIds. It shows the hierarchy of all the devices and modules including their IDs. This can help to define all your things in a configuration file.

Another way to get the IDs is to use the developer documentation on the netatmo site:

The IDs for the modules can be extracted from the developer documentation on the netatmo site. First login with your user. Then some examples of the documentation contain the real results of your weather station. In order to try the examples, you need the device_id of your Netatmo station. You can find it in the configuration menu of the app (android or apple). Get the IDs of your devices (indoor, outdoor, rain gauge) here (opens new window).

main_device is the ID of the "main device", the indoor sensor. This is equal to the MAC address of the Netatmo.

The other modules you can recognize by "module_name" and then note the "_id" which you need later.

Another way to get the IDs is to calculate them:

You have to calculate the ID for the outside module as follows: (it cannot be read from the app)

  • if the first serial character is "h": start with "02"
  • if the first serial character is "i": start with "03"
  • if the first serial character is "j": start with "04"
  • if the first serial character is "k": start with "05"

append ":00:00:",

split the rest into three parts of two characters and append with a colon as delimiter.

For example your serial number "h00bcdc" should end up as "02:00:00:00:bc:dc".

# Discovery

If you did not manually create things in the *.things file, the Netatmo Binding is able to discover automatically all depending modules and devices.

# Channels

# Weather Station Main Indoor Device

Weather station uses a default refreshInterval of 10 minutes (can be adjusted), based on a standard update period of Netatmo systems. It will auto-adapt to stick as closely as possible to the last data availability.

Supported channels for the main indoor module:

Channel Group Channel Id Item Type Description
pressure value Number:Pressure Current pressure
pressure absolute Number:Pressure Pressure at sea level
pressure trend String Pressure evolution trend over time
noise value Number:Dimensionless Current noise level
humidity value Number:Dimensionless Current humidity
humidity humidex Number Computed Humidex index
humidity humidex-scale Number Humidex index appreciation
temperature value Number:Temperature Current temperature
temperature min-today Number:Temperature Minimum temperature on current day
temperature max-today Number:Temperature Maximum temperature on current day
temperature min-time DateTime Moment of today's minimum temperature
temperature max-time DateTime Moment of today's maximum temperature
temperature trend String Temperature evolution trend over time
temperature heat-index Number:Temperature Computed Heat Index
temperature dewpoint Number:Temperature Computed dewpoint temperature
temperature dewpoint-depression Number:Temperature Computed dewpoint depression
airquality co2 Number:Dimensionless CO2 level in ppm
location value Location Location of the device
timestamp last-seen DateTime Last time the module reported its presence
timestamp measures DateTime Moment of the last measures update
signal strength Number Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Signal strength in dBm

All these channels are read only.

Extensible channels for the main indoor module:

Channel Type Item Type Description Channel parameters
co2-measurement Number:Dimensionless CO2 measurement limit (MIN, MAX), period (30min, 1hour, 3hours, 1day, 1week, 1month)
co2-timestamp DateTime CO2 measurement timestamp limit (DATE_MIN, DATE_MAX), period (1week, 1month)
hum-measurement Number:Dimensionless Humidity measurement limit (MIN, MAX), period (30min, 1hour, 3hours, 1day, 1week, 1month)
hum-timestamp DateTime Humidity measurement timestamp limit (DATE_MIN, DATE_MAX), period (1week, 1month)
noise-measurement Number:Dimensionless Noise measurement limit (MIN, MAX), period (30min, 1hour, 3hours, 1day, 1week, 1month)
noise-timestamp DateTime Noise measurement timestamp limit (DATE_MIN, DATE_MAX), period (1week, 1month)
pressure-measurement Number:Pressure Pressure measurement limit (MIN, MAX), period (30min, 1hour, 3hours, 1day, 1week, 1month)
pressure-timestamp DateTime Pressure measurement timestamp limit (DATE_MIN, DATE_MAX), period (1week, 1month)
temp-measurement Number:Temperature Temperature measurement limit (MIN, MAX), period (30min, 1hour, 3hours, 1day, 1week, 1month)
temp-timestamp DateTime Temperature measurement timestamp limit (DATE_MIN, DATE_MAX), period (1week, 1month)

# Weather Station Outdoor module

Supported channels for the outdoor module:

Channel Group Channel Id Item Type Description
humidity value Number:Dimensionless Current humidity
humidity humidex Number Computed Humidex index
humidity humidex-scale Number Humidex index appreciation
temperature value Number:Temperature Current temperature
temperature min-today Number:Temperature Minimum temperature on current day
temperature max-today Number:Temperature Maximum temperature on current day
temperature min-time DateTime Moment of today's minimum temperature
temperature max-time DateTime Moment of today's maximum temperature
temperature trend String Temperature evolution trend over time
temperature heat-index Number:Temperature Computed Heat Index
temperature dewpoint Number:Temperature Computed dewpoint temperature
temperature dewpoint-depression Number:Temperature Computed dewpoint depression
timestamp last-seen DateTime Last time the module reported its presence
timestamp measures DateTime Moment of the last measures update
signal strength Number Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Signal strength in dBm
battery value Number Battery level
battery low-battery Switch Low battery

All these channels are read only.

Extensible channels for the outdoor module:

Channel Type Item Type Description Channel parameters
hum-measurement Number:Dimensionless Humidity measurement limit (MIN, MAX), period (30min, 1hour, 3hours, 1day, 1week, 1month)
hum-timestamp DateTime Humidity measurement timestamp limit (DATE_MIN, DATE_MAX), period (1week, 1month)
temp-measurement Number:Temperature Temperature measurement limit (MIN, MAX), period (30min, 1hour, 3hours, 1day, 1week, 1month)
temp-timestamp DateTime Temperature measurement timestamp limit (DATE_MIN, DATE_MAX), period (1week, 1month)

# Weather Station Additional Indoor module

Supported channels for the additional indoor module:

Channel Group Channel Id Item Type Description
humidity value Number:Dimensionless Current humidity
humidity humidex Number Computed Humidex index
humidity humidex-scale Number Humidex index appreciation
temperature value Number:Temperature Current temperature
temperature min-today Number:Temperature Minimum temperature on current day
temperature max-today Number:Temperature Maximum temperature on current day
temperature min-time DateTime Moment of today's minimum temperature
temperature max-time DateTime Moment of today's maximum temperature
temperature trend String Temperature evolution trend over time
temperature heat-index Number:Temperature Computed Heat Index
temperature dewpoint Number:Temperature Computed dewpoint temperature
temperature dewpoint-depression Number:Temperature Computed dewpoint depression
airquality co2 Number:Dimensionless Air quality
timestamp last-seen DateTime Last time the module reported its presence
timestamp measures DateTime Moment of the last measures update
signal strength Number Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Signal strength in dBm
battery value Number Battery level
battery low-battery Switch Low battery

All these channels are read only.

Extensible channels for the additional indoor module:

Channel Type Item Type Description Channel parameters
co2-measurement Number:Dimensionless CO2 measurement limit (MIN, MAX), period (30min, 1hour, 3hours, 1day, 1week, 1month)
co2-timestamp DateTime CO2 measurement timestamp limit (DATE_MIN, DATE_MAX), period (1week, 1month)
hum-measurement Number:Dimensionless Humidity measurement limit (MIN, MAX), period (30min, 1hour, 3hours, 1day, 1week, 1month)
hum-timestamp DateTime Humidity measurement timestamp limit (DATE_MIN, DATE_MAX), period (1week, 1month)
temp-measurement Number:Temperature Temperature measurement limit (MIN, MAX), period (30min, 1hour, 3hours, 1day, 1week, 1month)
temp-timestamp DateTime Temperature measurement timestamp limit (DATE_MIN, DATE_MAX), period (1week, 1month)

# Rain Gauge

Supported channels for the rain guage:

Channel Group Channel Id Item Type Description
rain value Number:Speed Current precipitation intensity
rain sum-1 Number:Length Quantity of water over last hour
rain sum-24 Number:Length Quantity of water during the current day
timestamp last-seen DateTime Last time the module reported its presence
timestamp measures DateTime Moment of the last measures update
signal strength Number Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Signal strength in dBm
battery value Number Battery level
battery low-battery Switch Low battery

All these channels are read only.

Extensible channels for the rain guage:

Channel Type Item Type Description Channel parameters
sum_rain-measurement Number:Length Summing rain measurement period (30min, 1hour, 3hours, 1day, 1week, 1month)

# Weather Station Wind module

Supported channels for the wind module:

Channel Group Channel Id Item Type Description
wind angle Number:Angle Current 5 minutes average wind direction
wind strength Number:Speed Current 5 minutes average wind speed
wind max-strength Number:Speed Maximum wind strength recorded
wind max-strength-date DateTime Moment when MaxWindStrength was recorded
wind gust-angle Number:Angle Direction of the last 5 minutes highest gust
wind gust-strength Number:Speed Speed of the last 5 minutes highest gust wind
timestamp last-seen DateTime Last time the module reported its presence
timestamp measures DateTime Moment of the last measures update
signal strength Number Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Signal strength in dBm
battery value Number Battery level
battery low-battery Switch Low battery

All these channels are read only.

# Healthy Home Coach Device

Home Coach uses a default refreshInterval of 10 minutes (can be adjusted), based on a standard update period of Netatmo systems. It will auto-adapt to stick as closely as possible to the last data availability.

Supported channels for the healthy home coach device:

Channel Group Channel Id Item Type Description
noise value Number:Dimensionless Current noise level
humidity value Number:Dimensionless Current humidity
humidity humidex Number Computed Humidex index
humidity humidex-scale Number Humidex index appreciation
pressure value Number:Pressure Current pressure
pressure absolute Number:Pressure Pressure at sea level
temperature value Number:Temperature Current temperature
temperature min-today Number:Temperature Minimum temperature on current day
temperature max-today Number:Temperature Maximum temperature on current day
temperature min-time DateTime Moment of today's minimum temperature
temperature max-time DateTime Moment of today's maximum temperature
temperature heat-index Number:Temperature Computed Heat Index
temperature dewpoint Number:Temperature Computed dewpoint temperature
temperature dewpoint-depression Number:Temperature Computed dewpoint depression
airquality health-index Number Health index (*)
airquality co2 Number:Dimensionless Air quality
timestamp last-seen DateTime Last time the module reported its presence
timestamp measures DateTime Moment of the last measures update
signal strength Number Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Signal strength in dBm

(*) Health index values :

  • 0 : healthy
  • 1 : fine
  • 2 : fair
  • 3 : poor
  • 4 : unhealthy

All these channels are read only.

Extensible channels for the healthy home coach device:

Channel Type Item Type Description Channel parameters
hum-measurement Number:Dimensionless Humidity measurement limit (MIN, MAX), period (30min, 1hour, 3hours, 1day, 1week, 1month)
hum-timestamp DateTime Humidity measurement timestamp limit (DATE_MIN, DATE_MAX), period (1week, 1month)
noise-measurement Number:Dimensionless Noise measurement limit (MIN, MAX), period (30min, 1hour, 3hours, 1day, 1week, 1month)
noise-timestamp DateTime Noise measurement timestamp limit (DATE_MIN, DATE_MAX), period (1week, 1month)
pressure-measurement Number:Pressure Pressure measurement limit (MIN, MAX), period (30min, 1hour, 3hours, 1day, 1week, 1month)
pressure-timestamp DateTime Pressure measurement timestamp limit (DATE_MIN, DATE_MAX), period (1week, 1month)
temp-measurement Number:Temperature Temperature measurement limit (MIN, MAX), period (30min, 1hour, 3hours, 1day, 1week, 1month)
temp-timestamp DateTime Temperature measurement timestamp limit (DATE_MIN, DATE_MAX), period (1week, 1month)

# Thermostat Relay Device

Supported channels for the thermostat relay device:

Channel Group Channel Id Item Type Description
signal strength Number Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Signal strength in dBm

All these channels are read only.

# Thermostat Plug

Supported channels for the thermostat plug device:

Channel Group Channel Id Item Type Description
signal strength Number Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Signal strength in dBm

All these channels are read only.

# Room

Supported channels for the Room thing:

Channel Group Channel Id Item Type Description
temperature value Number:Temperature Current temperature in the room
properties window-open Contact Windows of the room are opened
properties anticipating Switch Anticipates next scheduled setpoint
properties heating-power-request Number:Dimensionless Percentage of heating power
setpoint value Number:Temperature Thermostat temperature setpoint
setpoint mode String Chosen thermostat mode (home, frost guard, manual, max)
setpoint start DateTime Start time of the currently applied setpoint
setpoint end DateTime End time of the currently applied setpoint

All these channels except setpoint and setpoint-mode are read only.

# Thermostat Module

Supported channels for the thermostat module:

Channel Group Channel Id Item Type Description
properties relay Contact Indicates if the boiler is currently heating
signal strength Number Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Signal strength in dBm
battery value Number Battery level
battery low-battery Switch Low battery
battery status String Description of the battery status (*)

(*) Can be UNDEF on some modules

# Valve Module

Supported channels for the Valve module:

Channel Group Channel Id Item Type Description
signal strength Number Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Signal strength in dBm
battery value Number Battery level
battery low-battery Switch Low battery
battery status String Description of the battery status (*)

# Home

A Home is the Thing holding various modules and devices. They can hold two areas of equipments : Security and Energy. Depending on the way it is configured the behaviour will be adapted and available channels can vary.

Home Configuration

The Home thing has the following configuration elements:

Parameter Type Required Description
id (1) String No If you have a single type of equipment, this id is to be used for the home
energyId String No Id of a home holding energy control devices
securityId String No Id of a home holding security monitoring devices
refreshInterval Integer No Refresh interval for refreshing the data in seconds. Default 180.

At least one of these parameter must be filled - at most two :

  • id or securityId
  • id or energyId
  • securityId and energyId

(1) this parameter is kept for backward compatibility.

All channels are read only.

Supported channels for the Security Home thing:

Channel Group Channel Id Item Type Description
security person-count Number Total number of persons that are at home
security unknown-person-count Number Total number of unknown persons that are at home
security unknown-person-picture Image Snapshot of unknown person that is at home

Supported trigger channels for the Security Home thing:

Supported trigger channels for the Security Home, Presence and Doorbell thing:

Channel Type ID Options Description
home-event A welcome home event is triggered directly via a configured webhook
PERSON Triggered when a concrete person was detected
PERSON_AWAY Triggered when a concrete person leaves
PERSON_HOME Triggered when a concrete person entered the home
OUTDOOR Triggered when a event of an outdoor camera was triggered
MOVEMENT Triggered when a movement was detected
HUMAN Triggered when a human was detected
ANIMAL Triggered when an animal was detected
VEHICLE Triggered when a vehicle was detected
NEW_MODULE Triggered when a new module was discovered
MODULE_CONNECT Triggered when a module gets connected
MODULE_DISCONNECT Triggered when a module gets disconnected
MODULE_LOW_BATTERY Triggered when the battery of a module gets low
MODULE_END_UPDATE Triggered when a firmware update of a module is done
CONNECTION Triggered when a camera connection gets created
DISCONNECTION Triggered when a camera connection got lost
ON Triggered when camera monitoring is switched on
OFF Triggered when camera monitoring is switched off
BOOT Triggered when a camera is booting
SD Triggered when a camera SD card status was changed
ALIM Triggered when a power supply status was changed
ACCEPTED_CALL Triggered when a doorbell call was accepted
INCOMING_CALL Triggered when a doorbell call is incoming
RTC Triggered when the doorbell button was pressed
MISSED_CALL Triggered when a doorbell call was missed

# Welcome, Presence and Doorbell Cameras

Warnings:

  • The URL of the live snapshot is a fixed URL so the value of the channel cameraLivePictureUrl / welcomeCameraLivePictureUrl will never be updated once first set by the binding. So to get a refreshed picture, you need to use the refresh parameter in your sitemap image element.
  • Some features like the video monitoring are accessed via the local network, so it may be helpful to set a static IP address for the camera within your local network.

Supported channels for the Welcome Camera thing:

Channel Group Channel ID Item Type Read/Write Description
security-event home-event Read-only Trigger channel which is triggered when the camera sent an event
status monitoring Switch Read-write State of the camera (video surveillance on/off)
status sd-card String Read-only State of the SD card
status alim String Read-only State of the power connector
live picture (**) Image Read-only Camera Live Snapshot
live local-picture-url String Read-only Local Url of the live snapshot for this camera
live vpn-picture-url String Read-only Url of the live snapshot for this camera through Netatmo VPN.
live local-stream-url (*) String Read-only Local Url of the live stream for this camera (accessible if openhab server and camera are located on the same lan.
live vpn-stream-url (*) String Read-only Url of the live stream for this camera through Netatmo VPN.
signal strength Number Read-only Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Read-only Signal strength in dBm
last-event type String Read-only Type of event
last-event subtype String Read-only Sub-type of event
last-event time DateTime Read-only Time of occurrence of event
last-event message String Read-only Message sent by Netatmo corresponding to given event
last-event snapshot Image Read-only picture of the last event, if it applies
last-event snapshot-url String Read-only If the last event (depending upon event type) in the home lead a snapshot picture, the picture URL will be available here
last-event local-video-url String Read-only If the last event (depending upon event type) in the home lead a snapshot picture, the corresponding local video URL will be available here
last-event vpn-video-url String Read-only If the last event (depending upon event type) in the home lead a snapshot picture, the corresponding VPN video URL will be available here
last-event video-status String Read-only Status of the video (recording, deleted or available)
last-event person-id String Read-only Id of the person the event is about (if any)

(*) This channel is configurable : low, poor, high. (**) This channel handles the REFRESH command for on demand update.

Supported channels for the Presence Camera thing:

Warnings:

  • The floodlight auto-mode (auto-mode) isn't updated it is changed by another application. Therefore the binding handles its own state of the auto-mode. This has the advantage that the user can define its own floodlight switch off behaviour.
Channel Group Channel ID Item Type Read/Write Description
security-event home-event Read-only Trigger channel which is triggered when the camera sent an event
status monitoring Switch Read-write State of the camera (video surveillance on/off)
status sd-card String Read-only State of the SD card
status alim String Read-only State of the power connector
live picture Image Read-only Camera Live Snapshot
live picture-url String Read-only Url of the live snapshot for this camera
live local-stream-url (*) String Read-only Local Url of the live stream for this camera (accessible if openhab server and camera are located on the same lan.
live vpn-stream-url (*) String Read-only Url of the live stream for this camera through Netatmo VPN.
signal strength Number Read-only Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Read-only Signal strength in dBm
presence floodlight String Read-write Sets the floodlight to ON/OFF/AUTO
presence siren Switch Read-write Status of the siren, if silent or emitting an alarm
last-event type String Read-only Type of event
last-event subtype String Read-only Sub-type of event
last-event time DateTime Read-only Time of occurrence of event
last-event message String Read-only Message sent by Netatmo corresponding to given event
last-event snapshot Image Read-only picture of the last event, if it applies
last-event snapshot-url String Read-only if the last event (depending upon event type) in the home lead a snapshot picture, the picture URL will be available here
last-event local-video-url String Read-only If the last event (depending upon event type) in the home lead a snapshot picture, the corresponding local video URL will be available here
last-event vpn-video-url String Read-only If the last event (depending upon event type) in the home lead a snapshot picture, the corresponding VPN video URL will be available here
last-event video-status String Read-only Status of the video (recording, deleted or available)
last-event person-id String Read-only Id of the person the event is about (if any)
sub-event type String Read-only Type of sub-event
sub-event time DateTime Read-only Time of occurrence of sub-event
sub-event message String Read-only Message sent by Netatmo corresponding to given sub-event
sub-event snapshot-url String Read-only Depending upon event type in the home, a snapshot picture of the corresponding local video URL will be available here
sub-event vignette-url String Read-only A vignette representing the snapshot
sub-event snapshot Image Read-only picture of the snapshot
sub-event vignette Image Read-only picture of the vignette

(*) This channel is configurable : low, poor, high.

Supported channels for the Doorbell thing:

Channel Group Channel ID Item Type Read/Write Description
security-event home-event Read-only Trigger channel which is triggered when the doorbell sent an event
status sd-card String Read-only State of the SD card
status alim String Read-only State of the power connector
live picture Image Read-only Camera Live Snapshot
live local-picture-url String Read-only Local Url of the live snapshot for this camera
live vpn-picture-url String Read-only Url of the live snapshot for this camera through Netatmo VPN.
signal strength Number Read-only Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Read-only Signal strength in dBm
last-event-doorbell type String Read-only Type of event
last-event-doorbell video-status String Read-only Status of the video (recording, deleted or available)
last-event-doorbell time DateTime Read-only Time of occurrence of event
last-event-doorbell local-video-url String Read-only If the last event (depending upon event type) in the home lead a snapshot picture, the corresponding local video URL will be available here
last-event-doorbell vpn-video-url String Read-only If the last event (depending upon event type) in the home lead a snapshot picture, the corresponding VPN video URL will be available here
sub-event-doorbell type String Read-only Type of sub-event
sub-event-doorbell time DateTime Read-only Time of occurrence of sub-event
sub-event-doorbell message String Read-only Message sent by Netatmo corresponding to given sub-event
sub-event-doorbell snapshot-url String Read-only Depending upon event type in the home, a snapshot picture of the corresponding local video URL will be available here
sub-event-doorbell vignette-url String Read-only A vignette representing the snapshot
sub-event-doorbell snapshot Image Read-only picture of the snapshot
sub-event-doorbell vignette Image Read-only picture of the vignette

Note: live feeds either locally or via VPN are not available in Netatmo API.

Supported channels for the Siren thing:

Channel Group Channel ID Item Type Read/Write Description
siren status Switch Read-only Status of the siren, if silent or emitting an alarm
siren monitoring Switch Read-only State of the siren device
signal strength Number Read-only Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Read-only Signal strength in dBm
timestamp last-seen DateTime Read-only Last time the module reported its presence
battery value Number Read-only Battery level
battery low-battery Switch Read-only Low battery

Supported channels for the Door Tag thing:

Channel Group Channel ID Item Type Read/Write Description
tag status Contact Read-only Status of tag (OPEN,CLOSED)
signal strength Number Read-only Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Read-only Signal strength in dBm
timestamp last-seen DateTime Read-only Last time the module reported its presence
battery value Number Read-only Battery level
battery low-battery Switch Read-only Low battery

# Welcome Person

Netatmo API distinguishes two kinds of persons:

  • Known persons : have been identified by the camera and you have defined a name for those.
  • Unknown persons : identified by the camera, but no name defined.

Person things are automatically created in discovery process for all known persons.

Supported channels for the Person thing:

Channel Group Channel ID Item Type Description
person avatar-url String URL for the avatar of this person
person avatar Image Avatar of this person
person at-home Switch Indicates if this person is known to be at home or not
person last-seen DateTime Moment when this person was last seen
last-event subtype String Sub-type of event
last-event message String Last event message from this person
last-event time DateTime Moment of the last event for this person
last-event snapshot Image Picture of the last event for this person
last-event snapshot-url String URL for the picture of the last event for this person
last-event camera-id String ID of the camera that triggered the event

All these channels except at-home are read only.

# Netatmo Smart Smoke Detector

All these channels are read only.

Supported channels for the Smoke Detector thing:

Channel Group Channel Id Item Type Description
signal strength Number Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Signal strength in dBm
timestamp last-seen DateTime Last time the module reported its presence
last-event type String Type of event
last-event time DateTime Moment of the last event for this person
last-event subtype String Sub-type of event
last-event message String Last event message from this person

# Netatmo Smart Carbon Monoxide Detector

All these channels are read only.

Supported channels for the Carbon Monoxide Detector thing:

Channel Group Channel Id Item Type Description
signal strength Number Signal strength (0 for no signal, 1 for weak...)
signal value Number:Power Signal strength in dBm
timestamp last-seen DateTime Last time the module reported its presence
last-event type String Type of event
last-event time DateTime Moment of the last event for this detector
last-event subtype String Sub-type of event
last-event message String Last event message from this detector

# Configuration Examples

# things/netatmo.things

Bridge netatmo:account:myaccount "Netatmo Account" [clientId="xxxxx", clientSecret="yyyy"] {
    Bridge weather-station inside "Inside Weather Station" [id="70:ee:aa:aa:aa:aa"] {
        outdoor outside   "Outside Module" [id="02:00:00:aa:aa:aa"] {
            Channels:
                Type hum-measurement : maxHumWeek [limit="MAX",period="1week"]
        }
        rain rainModule        "Rain Module"    [id="05:00:00:aa:aa:aa"] {
            Channels:
                Type sum_rain-measurement : rainThisWeek  "Rain This Week"     [period="1week"]
                Type sum_rain-measurement : rainThisMonth "Rain This Month"    [period="1month"]
        }
    }
    Bridge home myhome "My home" [ id="0123456789abcdef", refreshInterval=150 ] {
        Thing welcome mycam "My camera" [ id="70:aa:bb:cc:dd:ee" ] {
            Channels:
                Type live-stream-url : live#local-stream-url [ quality="high" ]
                Type live-stream-url : live#vpn-stream-url [ quality="low" ]
        }
    }
    Bridge home myhomeheating "Home heating" [ id="..." ] {
        Bridge plug relay "Boiler relay" [ id="..." ] {
            thermostat thermostat "Thermostat" [ id="..." ]
            valve valveoffice "Valve in office" [ id="..." ]
        }
        room office "Office" [ id="..." ]
    }
}

# items/netatmo.items

// Indoor Module
Number:Temperature   Indoor_Temp                       "Temperature [%.1f %unit%]"                                  <temperature>      { channel = "netatmo:weather-station:myaccount:inside:temperature#value" }
Number:Temperature   Indoor_Min_Temp                   "Min Temperature Today [%.1f %unit%]"                        <temperature>      { channel = "netatmo:weather-station:myaccount:inside:temperature#min-today" }
Number:Temperature   Indoor_Max_Temp                   "Max Temperature Today [%.1f %unit%]"                        <temperature>      { channel = "netatmo:weather-station:myaccount:inside:temperature#max-today" }
Number:Dimensionless Indoor_Humidity                   "Humidity [%d %unit%]"                                       <humidity>         { channel = "netatmo:weather-station:myaccount:inside:humidity#value" }
Number               Indoor_Humidex                    "Humidex [%.0f]"                                             <temperature_hot>  { channel = "netatmo:weather-station:myaccount:inside:humidity#humidex" }
Number:Temperature   Indoor_HeatIndex                  "HeatIndex [%.1f %unit%]"                                    <temperature_hot>  { channel = "netatmo:weather-station:myaccount:inside:temperature#heat-index" }
Number:Temperature   Indoor_Dewpoint                   "Dewpoint [%.1f %unit%]"                                     <temperature_cold> { channel = "netatmo:weather-station:myaccount:inside:temperature#dewpoint" }
Number:Temperature   Indoor_DewpointDepression         "DewpointDepression [%.1f %unit%]"                           <temperature_cold> { channel = "netatmo:weather-station:myaccount:inside:temperature#dewpoint-depression" }
Number:Dimensionless Indoor_Co2                        "CO2 [%d %unit%]"                                            <carbondioxide>    { channel = "netatmo:weather-station:myaccount:inside:airquality#co2" }
Number:Pressure      Indoor_Pressure                   "Pressure [%.1f %unit%]"                                     <pressure>         { channel = "netatmo:weather-station:myaccount:inside:pressure#value" }
Number:Pressure      Indoor_AbsolutePressure           "AbsolutePressure [%.1f %unit%]"                             <pressure>         { channel = "netatmo:weather-station:myaccount:inside:pressure#absolute" }
Number:Dimensionless Indoor_Noise                      "Noise [%d %unit%]"                                          <soundvolume>      { channel = "netatmo:weather-station:myaccount:inside:noise#value" }
Number               Indoor_RadioStatus                 "RadioStatus [%s]"                                          <signal>           { channel = "netatmo:weather-station:myaccount:inside:signal#strength" }
DateTime             Indoor_TimeStamp                  "TimeStamp [%1$td.%1$tm.%1$tY %1$tH:%1$tM]"                  <calendar>         { channel = "netatmo:weather-station:myaccount:inside:timestamp#measures" }
DateTime             Indoor_LastSeen            "LastSeen [%1$td.%1$tm.%1$tY %1$tH:%1$tM]"                          <text>             { channel = "netatmo:weather-station:myaccount:inside:timestamp#last-seen" }

// Outdoor Module
Number:Temperature   Outdoor_Temperature               "Temperature [%.1f %unit%]"                                  <temperature>      { channel = "netatmo:outdoor:myaccount:inside:outside:temperature#value" }
String               Outdoor_TempTrend                 "TempTrend [%s]"                                             <line>             { channel = "netatmo:outdoor:myaccount:inside:outside:temperature#trend" }
Number:Dimensionless Outdoor_Humidity                  "Humidity [%d %unit%]"                                       <humidity>         { channel = "netatmo:outdoor:myaccount:inside:outside:humidity#value" }
Number               Outdoor_Humidex                   "Humidex [%.0f]"                                             <temperature_hot>  { channel = "netatmo:outdoor:myaccount:inside:outside:humidity#humidex" }
Number:Temperature   Outdoor_HeatIndex                 "heat-index [%.1f %unit%]"                                   <temperature_hot>  { channel = "netatmo:outdoor:myaccount:inside:outside:temperature#heat-index" }
Number:Temperature   Outdoor_Dewpoint                  "Dewpoint [%.1f %unit%]"                                     <temperature_cold> { channel = "netatmo:outdoor:myaccount:inside:outside:temperature#dewpoint" }
Number:Temperature   Outdoor_DewpointDepression        "DewpointDepression [%.1f %unit%]"                           <temperature_cold> { channel = "netatmo:outdoor:myaccount:inside:outside:temperature#dewpoint-depression" }
Number               Outdoor_RadioStatus               "RfStatus [%.0f / 5]"                                        <signal>           { channel = "netatmo:outdoor:myaccount:inside:outside:signal#strength" }
Switch               Outdoor_LowBattery                "LowBattery [%s]"                                            <siren>            { channel = "netatmo:outdoor:myaccount:inside:outside:battery#low-battery" }
DateTime             Outdoor_TimeStamp                 "Measures TimeStamp [%1$td.%1$tm.%1$tY %1$tH:%1$tM]"         <calendar>         { channel = "netatmo:outdoor:myaccount:inside:outside:timestamp#measures" }
DateTime             Outdoor_LastMessage               "LastMessage [%1$td.%1$tm.%1$tY %1$tH:%1$tM]"                <text>             { channel = "netatmo:outdoor:myaccount:inside:outside:timestamp#last-seen" }

// Rain Module
Number:Speed         Rain_Intensity                    "Rain Intensity [%.1f %unit%]"                               <rain>             { channel = "netatmo:rain:myaccount:inside:rainModule:rain#value"}
Number:Length        Rain_Hour                         "Rain Last Hour [%.1f %unit%]"                               <rain>             { channel = "netatmo:rain:myaccount:inside:rainModule:rain#sum-1"}
Number:Length        Rain_Today                        "Rain Today [%.1f %unit%]"                                   <rain>             { channel = "netatmo:rain:myaccount:inside:rainModule:rain#sum-24"}

// Camera
Switch               CameraMonitoring                  "Monitoring"                                                 <switch>           { channel = "netatmo:welcome:myaccount:myhome:mycam:status#monitoring", autoupdate="false" }
String               CameraAlimState                   "Alim State [%s]"                                            <none>             { channel = "netatmo:welcome:myaccount:myhome:mycam:status#alim" }
String               CameraSDCardState                 "SD Card State [%s]"                                         <none>             { channel = "netatmo:welcome:myaccount:myhome:mycam:status#sd-card" }
Image                CameraLiveSnapshot                "Live Snapshot"                                              <none>             { channel = "netatmo:welcome:myaccount:myhome:mycam:live#picture" }
String               CameraLiveStreamLocalUrl          "Live Video Stream [%s]"                                     <none>             { channel = "netatmo:welcome:myaccount:myhome:mycam:live#local-stream-url" }
String               CameraLiveStreamVpnUrl            "Live Video Stream [%s]"                                     <none>             { channel = "netatmo:welcome:myaccount:myhome:mycam:live#vpn-stream-url" }
Number               CameraWifiStrength                "Wi-Fi Strength [%s]"                                        <wifi>             { channel = "netatmo:welcome:myaccount:myhome:mycam:signal#strength" }
DateTime             CameraEventTime                   "Event Timestamp [%1$tb %1$td %1$tH:%1$tM]"                  <time>             { channel = "netatmo:welcome:myaccount:myhome:mycam:last-event#time" }
String               CameraEventType                   "Event Type [%s]"                                            <none>             { channel = "netatmo:welcome:myaccount:myhome:mycam:last-event#type" }
String               CameraEventMessage                "Event Message [%s]"                                         <none>             { channel = "netatmo:welcome:myaccount:myhome:mycam:last-event#message" }
Image                CameraEventSnapshot               "Event Snapshot"                                             <none>             { channel = "netatmo:welcome:myaccount:myhome:mycam:last-event#snapshot" }
String               CameraEventStreamLocalUrl         "Event Video Stream [%s]"                                    <none>             { channel = "netatmo:welcome:myaccount:myhome:mycam:last-event#local-video-url" }
String               CameraEventStreamVpnUrl           "Event Video Stream [%s]"                                    <none>             { channel = "netatmo:welcome:myaccount:myhome:mycam:last-event#vpn-video-url" }
String               CameraEventVideoStatus            "Video Status [%s]"                                          <none>             { channel = "netatmo:welcome:myaccount:myhome:mycam:last-event#video-status" }
String               CameraEventPersonId               "Person Id [%s]"                                             <none>             { channel = "netatmo:welcome:myaccount:myhome:mycam:last-event#person-id" }

# sitemaps/netatmo.sitemap

sitemap netatmo label="Netatmo" {
    Frame label="Indoor" {
        Text item=Indoor_Temp
        Text item=Indoor_Min_Temp
        Text item=Indoor_Max_Temp
        Text item=Indoor_Min_Temp_TS
        Text item=Indoor_Max_Temp_TS
        Text item=Indoor_Humidity
        Text item=Indoor_Humidex                     valuecolor=[<20.1="green",<29.1="blue",<28.1="yellow",<45.1="orange",<54.1="red",>54.1="maroon"]
        Text item=Indoor_HeatIndex
        Text item=Indoor_Dewpoint
        Text item=Indoor_DewpointDepression
        Text item=Indoor_Co2                        valuecolor=[<800="green",<1000="orange",<1400="red",>1399="maroon"]
        Text item=Indoor_Pressure
        Text item=Indoor_AbsolutePressure
        Text item=Indoor_Noise
        Text item=Indoor_WifiStatus
        Text item=Indoor_TimeStamp
        Text item=Indoor_LastSeen
    }
    Frame label="Outdoor" { 
        Text item=Outdoor_Temperature
        Text item=Outdoor_TempTrend
        Text item=Outdoor_Humidity
        Text item=Outdoor_Humidex                    valuecolor=[<20.1="green",<29.1="blue",<28.1="yellow",<45.1="orange",<54.1="red",>54.1="maroon"]
        Text item=Outdoor_HeatIndex
        Text item=Outdoor_Dewpoint
        Text item=Outdoor_DewpointDepression
        Text item=Outdoor_RadioStatus
        Text item=Outdoor_LowBattery
        Text item=Outdoor_BatteryVP
        Text item=Outdoor_TimeStamp
        Text item=Outdoor_LastMessage
    }
    Frame label="Rain" {
        Text item=Rain_Intensity
        Text item=Rain_Hour
        Text item=Rain_Today
        Text item=Rain_Week
        Text item=Rain_Month
        Text item=Rain_BatteryVP
    }
    Frame label="Camera" icon="camera" {
        Switch item=CameraMonitoring
        Text item=CameraAlimState
        Text item=CameraSDCardState
        Text item=CameraWifiStrength
        Image item=CameraLiveSnapshot
        Text label="Live (local)" icon="none" {
            Video url="xxxxxx" item=CameraLiveStreamLocalUrl encoding="HLS"
        }
        Text label="Live (VPN)" icon="none" {
            Video url="xxxxxx" item=CameraLiveStreamVpnUrl encoding="HLS"
        }
        Text label="Last event" icon="none" {
            Text item=CameraEventTime
            Text item=CameraEventType
            Text item=CameraEventMessage
            Text item=CameraEventPersonId
            Image item=CameraEventSnapshot
            Text item=CameraEventVideoStatus
            Text label="Video (local)" icon="none" {
                Video url="xxxxxx" item=CameraEventStreamLocalUrl encoding="HLS"
            }
            Text label="Video (VPN)" icon="none" {
                Video url="xxxxxx" item=CameraEventStreamVpnUrl encoding="HLS"
            }
        }
    }
}

# Example Rules

rule "Notification on home web hook event"
when
Channel "netatmo:home:mybridgeid:myclientid:home-event" triggered
then
logInfo("camera", "Received web hook on home level")
end

rule "Notification on camera web hook event"
when
Channel "netatmo:presence:mybridgeid:myclientid:mythingid:home-event" triggered
then
logInfo("camera", "Received web hook on camera level")
end

# Rule Actions

Multiple actions are supported by this binding. In classic rules these are accessible as shown in this example (adjust getActions with your ThingId):

Example

 val actions = getActions("netatmo","netatmo:room:myaccount:myhome:livingroom")
 if(null === actions) {
        logInfo("actions", "Actions not found, check thing ID")
        return
 }

# setThermRoomTempSetpoint(temp,endtime)

Sends a temperature setpoint (and switch to manual mode) to the thermostat for a room with an end time.

Parameters:

Name Description
temp The temperature setpoint.
endtime Time the setpoint should end (Local Unix time in seconds).

Example:

actions.setThermRoomTempSetpoint(19.0, 1654387205)

# setThermRoomModeSetpoint(mode,endtime)

Sends a mode to the thermostat for a room with an optional end time.

Parameters:

Name Description
mode The mode to set: MANUAL, MAX or HOME.
endtime Time the setpoint should end (Local Unix time in seconds).

Example:

actions.setThermRoomModeSetpoint("MANUAL", 1654387205)
actions.setThermRoomModeSetpoint("HOME", null)

# Sample data

If you want to evaluate this binding but have not got a Netatmo station yourself yet, you can search on the web for a publicly shared weather station.

# Icons

The following icons are used by original Netatmo web app:

# Modules

  • https://my.netatmo.com/images/my/app/module_int.png
  • https://my.netatmo.com/images/my/app/module_ext.png
  • https://my.netatmo.com/images/my/app/module_rain.png

# Battery status

  • https://my.netatmo.com/images/my/app/battery_verylow.png
  • https://my.netatmo.com/images/my/app/battery_low.png
  • https://my.netatmo.com/images/my/app/battery_medium.png
  • https://my.netatmo.com/images/my/app/battery_high.png
  • https://my.netatmo.com/images/my/app/battery_full.png

# Signal status

  • https://my.netatmo.com/images/my/app/signal_verylow.png
  • https://my.netatmo.com/images/my/app/signal_low.png
  • https://my.netatmo.com/images/my/app/signal_medium.png
  • https://my.netatmo.com/images/my/app/signal_high.png
  • https://my.netatmo.com/images/my/app/signal_full.png

# Wifi status

  • https://my.netatmo.com/images/my/app/wifi_low.png
  • https://my.netatmo.com/images/my/app/wifi_medium.png
  • https://my.netatmo.com/images/my/app/wifi_high.png
  • https://my.netatmo.com/images/my/app/wifi_full.png
Caught a mistake or want to contribute to the documentation? Edit this page on GitHub (opens new window)

← Network →